![]() ![]() Take the thicker joint and use a screw or sharp implement to gently cut a small hole through it, about 2 to 3 cm from the filter. To get this, roll two classic joints, making sure that one is thinner than the other. This is smoke made from two joints that are fused to form an X or a cross. All that’s left is to attach the joints by wrapping a little tape around all three of their filters so that they stay in place while you make the braid.Īs soon as you have all three joints intertwined just like braiding someone’s hair, twist the tops of the joints to keep them all locked together and it’s a party! 5. Once you have three joints rolled this way, you’re good to go. All you need is three extra-long joints which you can easily make by sticking two rolling papers end to end for each joint. This is a triple coil joint and that gives you thrice the amount of smoke! And it’s pretty easy to pull off as long as you know how to make a braid. This joint is definitely for fans of intricate herbal origami. And presto! You have yourself an impressive scorpion joint. If you leave the king-sized joint open, you can elongate the tail of the scorpion by attaching more rolling paper with kief or honey oil, then when the extension is dry, fill it with weed and twist the end to close it. You can use some blunt glue to keep the entire structure in place. Bend the ends of the legs and pincers downwards so the joint can stand like a real scorpion. Then use smaller rolling papers to roll the joints that will make up the legs and pincers.Īttach the leg and pincer joints by poking holes along the king-sized joint with the tweezers the holes should be large enough to insert the smaller joints but not enough to rip the body of the scorpion open. To roll a scorpion joint, begin with using a king-sized rolling paper to roll a very fat joint which you will tie off or leave open depending on how long you want the tail of your scorpion to be. It does require a certain level of joint rolling mastery to accomplish, as well as a pair of needle-nose tweezers besides your usual joint-rolling tools. This joint is a scorpion made out of rolling paper and weed. ![]() This is where art sculptures merge with joint rolling to create a striking outcome. You might need a couple of tries to get this joint right but it’s really easy enough to do on an initial try. Once the paper is rolled and gummed, let it dry for a little while, and then fill the empty joint with your weed, gently tamping it down with your finger as you go to make sure the joint is fully loaded and still gives a nice even smoke. The easiest way to go about rolling a cone joint is to start by rolling the paper first, keeping the roll tight at the filter, and working it with your other hand so that it stays wide at the other end to give a cone finish. Cone joints are very popular and great for sharing since they contain more weed than the average joint. This cone joint is, just as its name implies, cone-shaped, which means that it is narrowest at the filter and widest at the tip. This is another simple and fairly classic way to roll a joint. ![]() ![]() When you have rolled the two slightly smaller-than-normal joints, all you then need to do is take a full-sized rolling paper and wrap it around both of them to seal them together, and your shotgun joint is ready to smoke. The only difference is that you need to reduce the width of two rolling papers by about a quarter each. Don’t forget to cut away from the side where the gum doesn’t go. It is a relatively simple joint to roll you just need to use all the techniques that you would when rolling classic cylindrical joints. This is very much the same idea behind the double doobie shotgun joint. Another analysis of the joint likens it to the front half of a car where you have the driver and the person riding a shotgun right next to them. It is a very popular untraditional rolling style among smokers because you get to enjoy twice the amount of fun with it. The shotgun joint is essentially a double joint that looks similar to the barrel of a shotgun. So if your curiosity has been piqued and you want to know some cool rolling techniques and unique designs that you can wow your buddies with, or you’re just looking to up the aesthetics of your smoking experience, here are 10 impressive ways to roll a joint today. Some of them are even downright crazy! Some of them are pure art and a lot of people genuinely love to have their joints rolled in these unique fashions. There now exist so many creative and impressive ways to roll a joint. If you are a member of the 420 community in the 21 st century, then you know that there is so much more to smoking than just your regular rolled joints. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |